Mboned M. Abrahamsson Internet-Draft T-Systems Intended status: Best Current Practice T. Chown Expires: May 3, 2018 Jisc L. Giuliano Juniper Networks, Inc. October 30, 2017 Deprecating ASM for Interdomain Multicast draft-acg-mboned-multicast-models-02 Abstract This document provides a high-level overview of more commonly used multicast service models, principally the Any-Source Multicast (ASM) and Source-Specific Multicast (SSM) models, and discusses the applicability of the models to certain scenarios. As a result, this document recommends that ASM is not used for interdomain scenarios, and the use of SSM is strongly recommended for all multicast scenarios. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on May 3, 2018. Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents Abrahamsson, et al. Expires May 3, 2018 [Page 1] Internet-Draft Deprecating Interdomain ASM October 2017 carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Multicast service models . . . . . . . . . . . . . . . . . . 3 3. Multicast building blocks . . . . . . . . . . . . . . . . . . 4 3.1. Multicast addressing . . . . . . . . . . . . . . . . . . 4 3.2. Host signalling . . . . . . . . . . . . . . . . . . . . . 4 3.3. Multicast snooping . . . . . . . . . . . . . . . . . . . 5 4. ASM service model protocols . . . . . . . . . . . . . . . . . 5 4.1. Protocol Independent Multicast, Dense Mode (PIM-DM) . . . 5 4.2. Protocol Independent Multicast, Sparse Mode (PIM-SM) . . 5 4.2.1. Interdomain PIM-SM, and MSDP . . . . . . . . . . . . 6 4.3. Bidirectional PIM (PIM-BIDIR) . . . . . . . . . . . . . . 6 4.4. IPv6 PIM-SM with Embedded RP . . . . . . . . . . . . . . 6 5. SSM service model protocols . . . . . . . . . . . . . . . . . 7 5.1. Source Specific Multicast (PIM-SSM) . . . . . . . . . . . 7 6. Discussion . . . . . . . . . . . . . . . . . . . . . . . . . 7 6.1. ASM Deployment . . . . . . . . . . . . . . . . . . . . . 7 6.2. SSM Deployment . . . . . . . . . . . . . . . . . . . . . 8 7. Recommendations on ASM and SSM deployment . . . . . . . . . . 8 7.1. Rationale - advantages of SSM . . . . . . . . . . . . . . 8 7.2. On deprecating interdomain ASM . . . . . . . . . . . . . 9 7.3. Intradomain ASM . . . . . . . . . . . . . . . . . . . . . 9 7.4. IGMPv3/MLDv2 support . . . . . . . . . . . . . . . . . . 10 7.5. Multicast addressing considerations . . . . . . . . . . . 10 7.6. Application considerations . . . . . . . . . . . . . . . 10 7.7. ASM/SSM transition - protocol mapping . . . . . . . . . . 11 8. Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . 11 9. Security Considerations . . . . . . . . . . . . . . . . . . . 12 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12 11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 12 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 12 12.1. Normative References . . . . . . . . . . . . . . . . . . 12 12.2. Informative References . . . . . . . . . . . . . . . . . 14 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15 1. Introduction IP Multicast has been deployed in various forms, both within private networks and on the wider Internet. While a number of service models have been published individually, and in many cases revised over time, there has been no strong recommendation made on the Abrahamsson, et al. Expires May 3, 2018 [Page 2] Internet-Draft Deprecating Interdomain ASM October 2017 appropriateness of the models to certain scenarios. This document aims to fill that gap, and includes a BCP-level recommendation to both deprecate the use of interdomain ASM and to promote the use of SSM for all multicast scenarios. 2. Multicast service models The general IP multicast service model [RFC1112] is that senders send to a multicast IP group address, receivers express an interest in traffic sent to a given multicast address, and that routers figure out how to deliver traffic from the senders to the receivers. The benefit of IP multicast is that it enables delivery of content such that any multicast packet sent from a source to a given multicast group address appears once and only once on any path between a sender and an interested receiver that has joined that multicast group. The principal advantage, in terms of bandwidth conservation will lie with the sender, i.e., at the head end. A reserved range of IP multicast group addresses (for either IPv4 or IPv6) is used for multicast group communication, as described in Section 3.1. Two high-level flavours of this service model have evolved over time. In Any-Source Multicast (ASM), any number of sources may transmit multicast packets, and those sources may come and go over the course of a multicast session without being known a priori. In ASM, receivers express interest only in a given multicast group address. In contrast, with Source-Specific Multicast (SSM) the specific source(s) that may send traffic to the group are known in advance. In SSM, receivers express interest both in a given multicast address and specific associated source address(es). Senders transmit multicast packets without knowing where receivers are, or how many there are. Receivers are able to signal to on-link routers their desire to receive multicast content sent to a given multicast group, and in the case of SSM from a specific sender IP address. They may discover the group (and sender IP) information in a number of different ways. They are also able to signal their desire to no longer receive multicast traffic for a given group (and sender IP). Multicast routing protocols are used to establish the multicast forwarding paths (tree) between a sender and a set of receivers. Each router would typically maintain multicast forwarding state for a given group (and potentially sender IP), such that it knows on which interfaces to forward (and where necessary replicate) multicast packets. Abrahamsson, et al. Expires May 3, 2018 [Page 3] Internet-Draft Deprecating Interdomain ASM October 2017 Multicast packet forwarding is generally not considered a reliable service. It is typically unidirectional, but a bidirectional multicast delivery mechanism also exists. 3. Multicast building blocks In this section we describe general multicast building blocks that are applicable to both ASM and SSM deployment. 3.1. Multicast addressing IANA has reserved specific ranges of IPv4 and IPv6 address space for multicast addressing. Guidelines for IPv4 multicast address assignments can be found in [RFC5771]. IPv4 has no explicit multicast address format; a specific portion of the overall IPv4 address space is reserved for multicast use (224.0.0.0/4). As per Section 9 of RFC5771, domains with a 32-bit ASN MAY apply for space in AD-HOC Block III, or instead consider using IPv6 multicast addresses. Guidelines for IPv6 multicast address assignments can be found in [RFC2375] and [RFC3307]. The IPv6 multicast address format is described in [RFC4291]. An IPv6 multicast group address will lie within ff00::/8. 3.2. Host signalling A host wishing to signal interest in receiving (or no longer receiving) multicast to a given multicast group (and potentially from a specific sender IP) may do so by sending a packet using one of the protocols described below on an appropriate interface. For IPv4, a host may use Internet Group Management Protocol Version 2 (IGMPv2) [RFC2236] to signal interest in a given group. IGMPv3 [RFC3376] has the added capability of specifying interest in receiving multicast packets from specific sources. For IPv6, a host may use Multicast Listener Discovery Protocol (MLD) [RFC2710] to signal interest in a given group. MLDv2 [RFC3810] has the added capability of specifying interest in receiving multicast packets from specific sources. Further guidance on IGMPv3 and MLDv2 is given in [RFC4604]. Abrahamsson, et al. Expires May 3, 2018 [Page 4] Internet-Draft Deprecating Interdomain ASM October 2017 3.3. Multicast snooping In some cases, it is desirable to limit the propagation of multicast messages in a layer 2 network, typically through a layer 2 switch device. In such cases multicast snooping can be used, by which the switch device observes the IGMP/MLD traffic passing through it, and then attempts to make intelligent decisions on which physical ports to forward multicast. Typically, ports that have not expressed an interest in receiving multicast for a given group would not have traffic for that group forwarded through them. There is further discussion in [RFC4541]. 4. ASM service model protocols 4.1. Protocol Independent Multicast, Dense Mode (PIM-DM) PIM-DM is detailed in [RFC3973]. It operates by flooding multicast messages to all routers within the network in which it is configured. This ensures multicast data packets reach all interested receivers behind edge routers. Prune messages are used by routers to tell upstream routers to (temporarily) stop forwarding multicast for groups for which they have no known receivers. PIM-DM remains an Experimental protocol since its publication in 2005. 4.2. Protocol Independent Multicast, Sparse Mode (PIM-SM) The most recent revision of PIM-SM is detailed in [RFC7761]. PIM-SM is, as the name suggests, was designed to be used in scenarios where the subnets with receivers are sparsely distributed throughout the network. PIM-SM supports any number of senders for a given multicast group, which do not need to be known in advance, and which may come and go through the session. PIM-SM does not use a flooding phase, making it more scalable and efficient than PIM-DM, but this means PIM-SM needs a mechanism to construct the multicast forwarding tree (and associated forwarding tables in the routers) without flooding the whole network. To achieve this, PIM-SM introduces the concept of a Rendezvous Point (RP) for a PIM domain. All routers in a PIM-SM domain are then configured to use specific RP(s). Such configuration may be performed by a variety of methods, including Anycast-RP [RFC4610]. A sending host's Designated Router encapsulates multicast packets to the RP, and a receiving host's Designated Router can forward PIM JOIN messages to the RP, in so doing forming what is known as the Rendezvous Point Tree (RPT). Optimisation of the tree may then Abrahamsson, et al. Expires May 3, 2018 [Page 5] Internet-Draft Deprecating Interdomain ASM October 2017 happen once the receiving host's router is aware of the sender's IP, and a source-specific JOIN message may be sent towards it, in so doing forming the Shortest Path Tree (SPT). Unnecessary RPT paths are removed after the SPT is established. 4.2.1. Interdomain PIM-SM, and MSDP PIM-SM can in principle operate over any network in which the cooperating routers are configured with RPs. But in general, PIM-SM for a given domain will use an RP configured for that domain. There is thus a challenge in enabling PIM-SM to work between multiple domains, i.e. to allow an RP in one domain to learn the existence of a source in another domain, such that a receiver's router in one domain can know to forward a PIM JOIN towards a source's Designated Router in another domain. The solution to this problem is to use an inter-RP signalling protocol known as Multicast Source Discovery Protocol (MSDP). [RFC3618]. Deployment scenarios for MSDP are given in [RFC4611]. MSDP remains an Experimental protocol since its publication in 2003. MSDP was not replicated for IPv6. 4.3. Bidirectional PIM (PIM-BIDIR) PIM-BIDIR is detailed in [RFC5015]. In contrast to PIM-SM, it can establish bi-directional multicast forwarding trees between multicast sources and receivers. 4.4. IPv6 PIM-SM with Embedded RP Within a single PIM domain, PIM-SM for IPv6 works largely the same as it does for IPv4. However, the size of the IPv6 address (128 bits) allows a different mechanism for multicast routers to determine the RP for a given multicast group address. Embedded-RP [RFC3956] specifies a method to embed the unicast RP IP address in an IPv6 multicast group address, allowing routers supporting the protocol to determine the RP for the group without any prior configuration, simply by observing the RP address that is embedded (included) in the group address. Embedded-RP allows PIM-SM operation across any IPv6 network in which there is an end-to-end path of routers supporting the protocol. By embedding the RP address in this way, multicast for a given group can operate interdomain without the need for an explicit source discovery protocol (i.e. without MSDP for IPv6). It would generally be desirable that the RP would be located close to the sender(s) in the group. Abrahamsson, et al. Expires May 3, 2018 [Page 6] Internet-Draft Deprecating Interdomain ASM October 2017 5. SSM service model protocols 5.1. Source Specific Multicast (PIM-SSM) PIM-SSM is detailed in [RFC4607]. In contrast to PIM-SM, PIM-SSM benefits from assuming that source(s) are known about in advance, i.e. the source IP address is known (by some out of band mechanism), and thus the receiver's router can send a PIM JOIN directly towards the sender, without needing to use an RP. IPv4 addresses in the 232/8 (232.0.0.0 to 232.255.255.255) range are designated as source-specific multicast (SSM) destination addresses and are reserved for use by source-specific applications and protocols. For IPv6, the address prefix FF3x::/32 is reserved for source-specific multicast use. 6. Discussion In this section we discuss the applicability of the ASM and SSM models described above, and their associated protocols, to a range of deployment scenarios. 6.1. ASM Deployment PIM-DM remains an Experimental protocol, that appears to be rarely used in campus or enterprise environments. In enterprise and campus scenarios, PIM-SM is in relatively common use. The configuration and management of an RP within a single domain is not onerous. However, if interworking with external PIM domains in IPv4 multicast deployments is needed, MSDP is required to exchange information between domain RPs about sources. MSDP remains an Experimental protocol, and can be a complex and fragile protocol to administer and troubleshoot. MSDP is also specific to IPv4; it was not carried forward to IPv6, in no small part due to the complexity of operation and troubleshooting. PIM-SM is a general purpose protocol that can handle all use cases. In particular, it was designed for cases where one or more sources may came and go during a multicast session. For cases where a single, persistent source is used, and receivers can be configured to know of that source, PIM-SM has unnecessary complexity. As stated above, MSDP was not taken forward to IPv6. Instead, IPv6 has Embedded-RP, which allows the RP address for a multicast group to be embedded in the group address, making RP discovery automatic, if all routers on the path between a receiver and a sender support the protocol. Embedded-RP can support lightweight ad-hoc deployments. Abrahamsson, et al. Expires May 3, 2018 [Page 7] Internet-Draft Deprecating Interdomain ASM October 2017 However, it does rely on a single RP for an entire group. Embedded- RP was run successfully between European and US academic networks during the 6NET project in 2004/05. Its usage generally remains constrained to academic networks. BIDIR-PIM is designed, as the name suggests, for bidirectional use cases. 6.2. SSM Deployment As stated in RFC4607, SSM is particularly well-suited to dissemination-style applications with one or more senders whose identities are known (by some mechanism) before the application starts running. PIM-SSM is therefore very well-suited to applications such as classic linear broadcast TV over IP. SSM requires hosts using it and (edge) routers with SSM receivers support the new(er) IGMPv3 and MLDv2 protocols. While delayed delivery of support in some OSes has meant that adoption of SSM has also been slower than might have been expected, or hoped, support for SSM is now widespread in common OSes. 7. Recommendations on ASM and SSM deployment This document recommends that the use of interdomain ASM is deprecated, i.e., only SSM is to be used for interdomain multicast. Further, it also strongly recommends the use of SSM for all multicast scenarios, be they run inter or intradomain. 7.1. Rationale - advantages of SSM A significant benefit of SSM is its reduced complexity through eliminating the network-based source discovery required in ASM. This means there are no RPs, shared trees, SPT switchover, PIM registers, MSDP or data-driven state creation elements to support. SSM is really just a small subset of PIM-SM, plus IGMPv3. This reduced complexity makes SSM radically simpler to manage, troubleshoot and operate, particularly for network backbone operators; this is the main motivation for the recommendation to deprecate the use of ASM in interdomain scenarios. Interdomain ASM is widely viewed as complicated and fragile. By eliminating network- based source discovery for interdomain multicast, the vast majority of the complexity issues go away. RFC 4607 includes details benefits of SSM, for example: Abrahamsson, et al. Expires May 3, 2018 [Page 8] Internet-Draft Deprecating Interdomain ASM October 2017 "Elimination of cross-delivery of traffic when two sources simultaneously use the same source-specific destination address; Avoidance of the need for inter-host coordination when choosing source-specific addresses, as a consequence of the above; Avoidance of many of the router protocols and algorithms that are needed to provide the ASM service model." Further discussion can also be found in [RFC3569]. SSM is considered more secure in that it supports access control, i.e. you only get packets from the sources you explicitly ask for, as opposed to ASM where anyone can decide to send traffic to a PIM-SM group address. This topic is expanded upon in [RFC4609]. 7.2. On deprecating interdomain ASM The recommendation to deprecate the use of interdomain ASM applies to the use of ASM between domains, where either MSDP (IPv4) or Embedded- RP (IPv6) is required for sharing knowledge of remote sources. If an organisation, or AS, wishes to use multiple multicast domains within its own network border, that is a choice for that organisation to make, and it may then use MSDP or Embedded-RP internally within its own network. MSDP is an Experimental level standard; this document does not propose making it Historic, given there may be such residual intra- organisation use cases. By implication, it is thus strongly recommended that SSM be the multicast protocol of choice for interdomain multicast. Best current practices for deploying interdomain multicast using SSM are documented in [I-D.ietf-mboned-interdomain-peering-bcp]. 7.3. Intradomain ASM The use of ASM within a single multicast domain, such as an enterprise or campus, with an RP for the site, is relatively common today. The site may also choose to use Anycast-RP or MSDP for RP resilience, at the expense of the extra complexity in managing that configuration. Regardless, this document does not preclude continued use of ASM in the intradomain scenario. However, it is strongly recommended that sites using ASM internally conduct an audit of the multicast applications used, and begin planning a migration to using SSM instead wherever possible. Abrahamsson, et al. Expires May 3, 2018 [Page 9] Internet-Draft Deprecating Interdomain ASM October 2017 7.4. IGMPv3/MLDv2 support This document recommends that all host and router platforms supporting multicast also support IGMPv3 and MLDv2. The updated IPv6 Node Requirements RFC [I-D.ietf-6man-rfc6434-bis] states that MLDv2 support is a MUST in all implementations. Such support is already widespread in common host and router platforms. 7.5. Multicast addressing considerations A key benefit of SSM is that the multicast application does not need to be allocated a specific multicast group by the network, rather as SSM is inherently source-specific, it can use any group address, G, in the reserved range of IPv4 or IPv6 SSM addresses for its own source address, S. In principle, if interdomain ASM is deprecated, backbone operators could begin filtering the ranges of group addresses used by ASM. In practice, this is not recommended given there will be a transition period from ASM to SSM, as discussed in Section 7.7, where some form of ASM-SSM mappings may be used, and filtering may preclude such operations. 7.6. Application considerations There will be a wide range of applications today that only support ASM, whether as software packages, or code embedded in devices such as set top boxes. The strong recommendation in this document for use of SSM means that applications should instead use SSM, should operate correctly in an SSM environment, and thus trigger IGMPv3/MLDv2 messages to signal use of SSM. It is often thought that ASM is required for multicast applications where there are multiple sources. However, RFC4607 also describes how SSM can be used instead of PIM-SM for multi-party applications: "SSM can be used to build multi-source applications where all participants' identities are not known in advance, but the multi- source "rendezvous" functionality does not occur in the network layer in this case. Just like in an application that uses unicast as the underlying transport, this functionality can be implemented by the application or by an application-layer library." Thus, in theory, it should be possible to port ASM-only applications to be able to run using SSM, if an appropriate out-of-band mechanism can be chosen to convey the participant source addresses. Abrahamsson, et al. Expires May 3, 2018 [Page 10] Internet-Draft Deprecating Interdomain ASM October 2017 Given all common OSes support SSM, it is then down to the programming language and APIs used as to whether the necessary SSM APIs are available. SSM support is generally quite ubiquitous, with the current exception of websockets used in web-browser based applications. It is desirable that applications also support appropriate congestion control, as described in [RFC8085], with appropriate codecs, to achieve the necessary rate adaption. It is recommended that application developers choosing to use multicast, develop and engineer their applications to use SSM rather than ASM. Some useful considerations for multicast applications can still be found in the relatively old [RFC3170]. 7.7. ASM/SSM transition - protocol mapping In the case of existing ASM applications that cannot readily be ported to SSM, it may be possible to use some form of protocol mapping, i.e., to have a mechanism to translate a (*,G) join or leave to a (S,G) join or leave, for a specific source, S. The general challenge in performing such mapping is determining where the configured source address, S, comes from. There are some existing vendor-specific mechanisms to achieve this function, but none are documented in IETF standards. This may be an area for the IETF to work on, but it should be noted that any such effort would only be an interim transition mechanism, and such mappings do not remove the requirement for applications to be allocated ASM group addresses for the communications. It is generally considered better to work towards using SSM, and thus pushing the source discovery problem from the network to the application. 8. Conclusions This document recommends that the use of interdomain ASM is deprecated. It also recommends the use of SSM for all multicast scenarios. Specific implications and considerations for the recommendation are discussed. Abrahamsson, et al. Expires May 3, 2018 [Page 11] Internet-Draft Deprecating Interdomain ASM October 2017 9. Security Considerations This document adds no new security considerations. RFC4609 describes the additional security benefits of using SSM instead of ASM. 10. IANA Considerations This document currently makes no request of IANA. Note to RFC Editor: this section may be removed upon publication as an RFC. 11. Acknowledgments The authors would like to thank the following people for their contributions to the document: Hitoshi Asaeda, Dale Carder, Toerless Eckert, Jake Holland, Mike McBride, Per Nihlen, Greg Shepherd, Stig Venaas, Nils Warnke, and Sandy Zhang. 12. References 12.1. Normative References [RFC1112] Deering, S., "Host extensions for IP multicasting", STD 5, RFC 1112, DOI 10.17487/RFC1112, August 1989, . [RFC2236] Fenner, W., "Internet Group Management Protocol, Version 2", RFC 2236, DOI 10.17487/RFC2236, November 1997, . [RFC2375] Hinden, R. and S. Deering, "IPv6 Multicast Address Assignments", RFC 2375, DOI 10.17487/RFC2375, July 1998, . [RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast Listener Discovery (MLD) for IPv6", RFC 2710, DOI 10.17487/RFC2710, October 1999, . [RFC3170] Quinn, B. and K. Almeroth, "IP Multicast Applications: Challenges and Solutions", RFC 3170, DOI 10.17487/RFC3170, September 2001, . [RFC3307] Haberman, B., "Allocation Guidelines for IPv6 Multicast Addresses", RFC 3307, DOI 10.17487/RFC3307, August 2002, . Abrahamsson, et al. Expires May 3, 2018 [Page 12] Internet-Draft Deprecating Interdomain ASM October 2017 [RFC3376] Cain, B., Deering, S., Kouvelas, I., Fenner, B., and A. Thyagarajan, "Internet Group Management Protocol, Version 3", RFC 3376, DOI 10.17487/RFC3376, October 2002, . [RFC3569] Bhattacharyya, S., Ed., "An Overview of Source-Specific Multicast (SSM)", RFC 3569, DOI 10.17487/RFC3569, July 2003, . [RFC3618] Fenner, B., Ed. and D. Meyer, Ed., "Multicast Source Discovery Protocol (MSDP)", RFC 3618, DOI 10.17487/RFC3618, October 2003, . [RFC3810] Vida, R., Ed. and L. Costa, Ed., "Multicast Listener Discovery Version 2 (MLDv2) for IPv6", RFC 3810, DOI 10.17487/RFC3810, June 2004, . [RFC3956] Savola, P. and B. Haberman, "Embedding the Rendezvous Point (RP) Address in an IPv6 Multicast Address", RFC 3956, DOI 10.17487/RFC3956, November 2004, . [RFC3973] Adams, A., Nicholas, J., and W. Siadak, "Protocol Independent Multicast - Dense Mode (PIM-DM): Protocol Specification (Revised)", RFC 3973, DOI 10.17487/RFC3973, January 2005, . [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006, . [RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for IP", RFC 4607, DOI 10.17487/RFC4607, August 2006, . [RFC4610] Farinacci, D. and Y. Cai, "Anycast-RP Using Protocol Independent Multicast (PIM)", RFC 4610, DOI 10.17487/RFC4610, August 2006, . [RFC5015] Handley, M., Kouvelas, I., Speakman, T., and L. Vicisano, "Bidirectional Protocol Independent Multicast (BIDIR- PIM)", RFC 5015, DOI 10.17487/RFC5015, October 2007, . Abrahamsson, et al. Expires May 3, 2018 [Page 13] Internet-Draft Deprecating Interdomain ASM October 2017 [RFC5771] Cotton, M., Vegoda, L., and D. Meyer, "IANA Guidelines for IPv4 Multicast Address Assignments", BCP 51, RFC 5771, DOI 10.17487/RFC5771, March 2010, . [RFC7761] Fenner, B., Handley, M., Holbrook, H., Kouvelas, I., Parekh, R., Zhang, Z., and L. Zheng, "Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol Specification (Revised)", STD 83, RFC 7761, DOI 10.17487/RFC7761, March 2016, . 12.2. Informative References [RFC4541] Christensen, M., Kimball, K., and F. Solensky, "Considerations for Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) Snooping Switches", RFC 4541, DOI 10.17487/RFC4541, May 2006, . [RFC4604] Holbrook, H., Cain, B., and B. Haberman, "Using Internet Group Management Protocol Version 3 (IGMPv3) and Multicast Listener Discovery Protocol Version 2 (MLDv2) for Source- Specific Multicast", RFC 4604, DOI 10.17487/RFC4604, August 2006, . [RFC4609] Savola, P., Lehtonen, R., and D. Meyer, "Protocol Independent Multicast - Sparse Mode (PIM-SM) Multicast Routing Security Issues and Enhancements", RFC 4609, DOI 10.17487/RFC4609, October 2006, . [RFC4611] McBride, M., Meylor, J., and D. Meyer, "Multicast Source Discovery Protocol (MSDP) Deployment Scenarios", BCP 121, RFC 4611, DOI 10.17487/RFC4611, August 2006, . [RFC8085] Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage Guidelines", BCP 145, RFC 8085, DOI 10.17487/RFC8085, March 2017, . [I-D.ietf-mboned-interdomain-peering-bcp] Tarapore, P., Sayko, R., Shepherd, G., Eckert, T., and R. Krishnan, "Use of Multicast Across Inter-Domain Peering Points", draft-ietf-mboned-interdomain-peering-bcp-13 (work in progress), October 2017. Abrahamsson, et al. Expires May 3, 2018 [Page 14] Internet-Draft Deprecating Interdomain ASM October 2017 [I-D.ietf-6man-rfc6434-bis] Chown, T., Loughney, J., and T. Winters, "IPv6 Node Requirements", draft-ietf-6man-rfc6434-bis-02 (work in progress), October 2017. Authors' Addresses Mikael Abrahamsson T-Systems Stockholm Sweden Email: mikael.abrahamsson@t-systems.se Tim Chown Jisc Lumen House, Library Avenue Harwell Oxford, Didcot OX11 0SG United Kingdom Email: tim.chown@jisc.ac.uk Lenny Giuliano Juniper Networks, Inc. 2251 Corporate Park Drive Hemdon, Virginia 20171 United States Email: lenny@juniper.net Abrahamsson, et al. Expires May 3, 2018 [Page 15]